Shaped, Flat, Square, Round, Fine, Plated and Bare Wire ASTM A167, AMS 5523
Application
Furnace parts
Heat Exchangers
Paper Mill Equipment
Exhaust Parts in Gas Turbines
Jet Engine Parts
Oil Refinery Equipment
Chemistry Typical
Carbon |
0.080 max |
Manganese |
2.00 max |
Silicon |
0.75 max |
Chromium |
24.00- 26.00 |
Nickel |
19.00- 22.00 |
Molybdenum |
0.75 max |
Phosphorus |
0.040 max |
Physical Properties
Density | 0.29 lbs/in³ 9.01 g/cm³ |
Electrical Resistivity | microhm-in (microhm-cm) |
68°F (20°C) | 37.0 (94.0) |
Specific Heat | BTU/lb/°F (kJ/kg•K) |
32-212°F (0-100°C) | 0.12 (0.50) |
Thermal Conductivity | BTU/hr/ft²/ft/°F (W/m•K) |
At 212°F (100°C) | 8.0 (13.8) |
At 932°F (500°C) | 10.8 (18.7) |
Mean Coefficient of Thermal Expansion | in/in/°F (μm/m•K) |
32-212°F (0-100°C) | 8.0 x 10 (14.4) |
32-600°F (0-315°C) | 9.3 x 10 (16.7) |
32-1000°F (0-538°C) | 9.6 x 10 (17.3) |
32-1200°F (0-649°C) | 9.7x 10 (17.5) |
Modulus of Elasticity | KSI (MPa) 29.0 x 10³ (200 x 10³) in tension 11.2 x 10³ ( 78 x 10³) in torsion |
Magnetic Permeability | H = 200 Oersteds |
Annealed | < 1.02 max |
Melting Range | °F (°C) 2550 – 2650 (1399 – 1454) |
Mechanical Properties
Mechanical Properties At Room Temperature
PROPERTIES | ANNEALED |
Ultimate Tensile Strength | 75 KSI min (515 MPA min) |
Yield Strength (0.2% offset) | 30 KSI min (205 MPA min) |
Elongation | 40% min Hardness Rb 95 max |
Properties | Tempered 310S can be supplied in a various rolled tempered conditions. |
Contact Ulbrich Technical Service for details.
Corrosion Resistance
Refer to NACE (National Association of Corrosion Engineers) for recommendations.
Properties Tempered Alloy 310S can be cold rolled to achieve the temper properties required by specific customers and/or manufacturing requirements. Contact Ulbrich Wire for details.
Forms
Continuous Coils Cut to lengths Precision cutting
Cold Forming Alloy 310S has a good ductility and can be rolled formed, stamped and drawn readily.
Heat Treatment Alloy 310S can only be hardened by cold working.
Welding For best results refer to: SSINA’s “Welding of Stainless Steels and Other Joining
Methods”.
Limitation of Liability and Disclaimer of Warranty: In no event will Ulbrich Stainless Steels and Special Metals, Inc., be liable for any damages arising from the use of the information included in this document or that it is suitable for the ‘applications’ noted. We believe the information and data provided to be accurate to the best of our knowledge but, all data is considered typical values only. It is intended for reference and general information and not recommended for specification, design or engineering purposes. Ulbrich assumes no implied or express warranty in regard to the creation or accuracy of the data provided in this document.